- 2023
- Apr
- 16
Cuyahoga Falls Amateur Radio Club Hamfest, 2023 show pictures
This year’s show was about the same number of vendors as last year, so it was pretty good. There seemed to be more general electronics and whatnot this year, and less test equipment and other non-consumer items. Not really a big deal, there was still plenty to look at, including some vendors that I recognized from last year. I didn’t take as many pictures because of that, and missed some opportunities to get more because a friend I hadn’t seen in 18 years showed up and we were chatting the whole time.
In all, it was a decent show and worth the trip. While I only brought home about as much as I did from the TMRA show, it was only because I had to stop myself from dragging home more - there were a number of things I’d have like to had, but just do not have the room.
Enjoy the pictures, and I’ll be posting my haul a little later.. I found an unusual piece of equipment from a manufacturer that you wouldn’t expect to make something like it is, and I’ll be breaking that out into a separate post - if I can find it’s service data, it will be a technical post as well.
- 2023
- Apr
- 13
The Tusco ARC Hamfest
I’ve never been to this show, but it’s close enough that I’ll check it out. They claim this is the first one since the world decided that a runny nose was cause for martial law, hopefully some good stuff will show up. See you there, and as always, stay tuned for pictures of the event.
When:
Saturday April 22nd, 2023 8A-??
Where:
Tuscarawas County Fair Grounds
259 S Tuscarawas Ave
Dover, OH 44622
(Must Enter Through the Tuscarawas Ave Gate)
Admission is $5.00 per person.
https://www.w8zx.net/hamfest
- 2023
- Apr
- 13
The 67th Cuyahoga Falls ARC Hamfest
This show was excellent last year, and I’m looking forward to attending this year. Unless something major comes up, I’ll see you there!
When:
Saturday April 15th 2023, 8A-1P
Where:
Emidio & Sons Party Center
48 E. Bath Road
Cuyahoga Falls, Ohio 44221
Admission is $7.00 per person.
Stay tuned for pictures of the event.
https://sites.google.com/cfarc.org/cfarc/hamfest
- 2023
- Mar
- 19
The TMRA Hamfest Haul
I was kind of disappointed, nothing really stuck out at me and I didn’t see anything picture worthy. The only real item, other than some parts, was a nice old Hickock DVM with VFD tubes, but someone picked it up and put it on their own table for resale (at a higher price of course.) I don’t need another meter but eh…
I don’t know if it’s because of the area, because what I’m looking for didn’t show up, or because there didn’t seem to be as much general electronics as I’d expect, I only came home with trinkets.
A sleeve of 35W4, because you always need more of those, a couple of books, some insulated drivers, and some parts are all I took home. There are more shows coming up, so we’ll see what happens.
- 2023
- Mar
- 19
Random board shot - a commercial weather radio.
It’s always interesting to open a device and see ancient chips you’ve never run across before. The LM389 is a LM386 with three transistors for RF, IF, and 2nd IF on the substrate. This ancient commercial weather radio uses one for it’s audio final, if I want to keep it in operation it’s probably best to find a couple of spares along with the MC3357 IF chip next door. This device was made in the USA, even the circuit board was made right here in Ohio as evidenced by the GE Textolite “T” in the substrate of the board.
It’s well built, but the electrolytic capacitors with the long leads surprise me. I would think for a device with RF floating around inside, you’d want to keep those short.
It needs a new power cord, the old one is short and worn, as well as some DeOxit sprayed in the controls and switches. I may also replace the power supply filter capacitor, but that’s only because it was laying against the regulator for untold years and has a nice discolored spot on it.
More on this device later…
- 2023
- Mar
- 12
A General Electric T-125A “All American Five” Radio, Part III
This is part 3, and the final part of working with this radio. It didn’t turn out as good as I’d hoped, some of the other capacitors are leaky - and some of those are in a couplet. The customer just wanted it to make voices come from the air, so I’ve left it at that for now.
The original diagnosis I came up with was bad filters, and that was the case. The original electrolytic capacitors were bad, and were simply acting as opens instead of capacitors. The device in questions was a dual section, wax sealed tubular device, consisting of a 50uF and a 30uF part. I chose to replace them with Cornell-Dublier 47uF capacitors, which should be good for another 50 years. The across-the-line capacitor also got replaced with a Vishay 0.047uF @ 600VDC device. Just as good as the original without the bumblebomb problems.
The parts, fresh from Mouser:
What we’re working with. The black tubular part in front, and the metal cased tube in back are the suspects. If you look in the middle of the board, you’ll see a reddish-brown rectangle That’s the couplet, and was a cost-saving multi-part unit. When they go bad you rebuild what’s in them…
Other problems reared their head as it was being taken apart. The biggest is the age of the plastics. The knob used a metal band on the plastic to tension it on the shaft of the tuning capacitor. Pulling this knob from the shaft left the tension band on the shaft (it had little ears that were probably used during manufacture as an install aid,) and the plastic is so brittle and dried out that it just crumbles to dust. There was enough left to put it back on, so I broke the ears on the band off and replaced the tension band and said “Don’t touch this again” to myself.
The other bad thing, and something I didn’t notice before, is the speaker had a tear. The paper was so rotten it felt like wet tissue and just kept tearing itself. Well, it still works, and this can be replaced easily enough if desired.
So, on to the repair. It was a simple matter to desolder the parts, the heavy copper on the board let it’s old solder go with a 35W iron and some wick. The parts pulled out easily and the board cleaned up well.
You’ll notice the board is discolored. That’s where the 50C5 power amp tube sits, and it gets toasty. The solder joints are exhibiting potential cracks, so they all got touched up.
The parts I installed were much smaller than their vintage counterparts, so they got bent leads to sit down on the board, and were just placed in the board. I wasn’t going for a beauty contest here, they need to be in there solid and electrically correct. You’ll notice the one electrolytic is offset a bit, I realized after I put one in that the banana slicer had one section larger than the other. Oops…that other part goes in the parts bin.
For the filters, I just jumped the two together with a loop, looped a piece of bare wire around the common and soldered it all together. The original capacitor was full of old wax and wasn’t being rebuilt.
It was all back together…but there was still no joy. The filters took care of the buzz, and the output was nice and strong - then it started to fade and get fuzzy as something started leaking. One of the coupling capacitors or other small filters on the plates is probably leaky and drawing things out of tolerance, or a tube is bad. On a whim, I tested a few of the tubes, and they seem ok, so it’s probably one of the capacitors. With some being in that couplet, that’s more of a job that a “I’ll take a look” can cover.
A short clip of the radio playing. When it’s first turned on, it’s nice and strong but fades quickly. Sorry about the download, Youtube has decided that I need to verify my identity once again, and I’m done with that game.
https://privateemail … 9e11/1/8/NjE/NjEvMTA
It goes back the owner this week, if they want more repairs that’s a different proposition. Some of the younger members of that family are starting to get into electronics, perhaps this is a good project 15 years down the road.
Beyond that, it’s really not cost-effective to repair something like this for someone else unless they understand it’s basically a replace everything deal.
- 2023
- Feb
- 28
The Breezeshooter’s Hamfest 2023
I just noticed that the Breezeshooter’s club in PA is holding their annual hamfest again this year, after several years of everyone’s television saying we were all going to die.
While the details are scarce, it appears to be happening the first weekend in June (3rd and ?4th?) - this has always been a good show when I’ve attended, and has a lot of good deals and eye candy. I’ll post more details as they become available.
- 2023
- Feb
- 28
A General Electric T-125A “All American Five” Radio, Part II
A short update: I decided to just order some good quality parts from Mouser instead of trying to pick through the junk at a show.
While they’d probably be cheaper at a show, the three parts I need to get this radio playing cost less than $7, and that’s just because I decided to go a bit higher in quality than absolutely necessary. I should have them in hand Friday, and it won’t take long at all to get them installed.
Stand by for part 3.
- 2023
- Feb
- 7
A General Electric T-125A “All American Five” Radio
This is a radio a co-worker rescued from a barn sale, and wanted to know if it could be made to work again. The T-125A was manufactured between 1958 and 1962 (or 1963, depending on who you believe.) It still has the civil defense markings on the dial, so this radio was probably one of GE’s last radios to have this marking.
The radio apparently spent the majority of it’s life in a woodshop, and it shows. While the case plastic is in excellent condition with no chips or cracks, it’s stained with various wood coloring products. Back and original cord are present and intact, although the cord is getting stiff. It, however, exhibits no cracking so it will get left as-is for now. The inside of the radio shows you where it was for most of it’s life, being coated with wood dust.
Since these are simple inside, there wasn’t any need to grab an isolation transformer or variac, just plug the thing in. The worst that would happen would be the across-the-line capacitor would pop, so…
It exhibits exactly what you’d expect. A loud 60Hz hum, so the filters are bad. That was completely expected. It’s a dual section filter consisting of a 50uF and a 30uF capacitor, so I’m simply going to get two 47uF @ 150V caps and replace it. The across-the-line cap is .047uF at 600, it will be replaced with something similar. The only other suspect item would be the coupling capacitor between the detector and the power amplifier, so it will probably get replaced as well. The grid capacitors could be eyed with suspicion, but I’m going to leave those alone unless they show problems. One is in a couplet, which would require rebuilding the device if it’s bad.
The owner simply wants it to play long enough to go “Hey, that’s cool.”
A quick cleaning with a paintbrush and some canned air got rid of most of the dirt:
So it’s ready to repair. I’ll pick up some parts at the next few hamfests I attend.
One interesting thing about this radio is the 50C5 power amp tube. It has different color writing, so I assume it’s a (genuine GE) replacement tube. It still has something interesting about it - the getter is black. I can’t say I’ve ever seen one like this without the tube being red-plated. I have to assume this radio was on for most of it’s life. Pretty cool.
Off to a show for parts. Check back later for results on this radio.
The GE T-125A schematic.
Courtesy of radiomuseum.org
https://privateemail … 729ec/1/8/NjQ/NjQvOQ
- 2023
- Jan
- 29
Addendum to the hamfest list…
As much as I’d like to make it to the Toledo show, that may not be possible this year due to the drive. I’m still going to try, however.
In the meantime, I may try to get to the show in Dover, OH at the fairgrounds. According to the information, this is their first show since 2019, so people may be itching to get out and bring their junk out for sale.
TUSCO Amateur Radio Club Hamfest
Sunday, April 22nd, 2023. 8A-1P
Tuscarawas County Fairgrounds
295 South Tuscarawas Street
Dover, OH 44622
The flyer notes to enter through the Tuscarawas Ave gate.
https://forums.qrz.com/index.php?threads/tusco-hamfest-dover-ohio-april-22-2023.848201/#post-6430335